Marathon-computer Vertical Recycler Baler V-4224 Bedienungsanleitung

PLAY IT SAFE!OPERATION, MAINTENANCEAND INSTALLATION MANUALFORVERTICAL RECYCLER BALERV-4224Marathon Equipment Co. OMI Manual No. 0011CE, Rev. 02/02VERN

DIAGRAM - BALE TIE OFF/BALE EJECTFRONT VIEW OF BALERBALE TIE - TIGHTENEDHAND TIGHTBALE DURINGEJECTIONPALLET OR BALE CARTRECOMMENDED FORSUPPORTING BALE

TIE SLOT CLEANING1-9FRONT VIEWBALEFEED GATETIE SLOTSSLOT CLEANING TOOLHANDLEAT TIMES THE TIE SLOTS MAY BECOME OBSTRUCTED WITH MATERIAL AND PREVENT THE

WARNING DECAL REQUIREMENTSWhen your baler leaves the factory, several WARNING DECALS are installed forprotection. These labels are subjec

DECAL PLACEMENT1-111 OPERATION

2 MAINTENANCELOCK-OUT & TAG-OUT INSTRUCTIONS06-0045460VOLTSDANGERELECTRICAL: The panel box contains high voltagecomponents. Only authorized se

SUPPORTING OF PLATENBALE CHAMBERDOOR, OPENFEED GATE OPEN -PLATEN IN UPPOSITION100mm x100mmWOOD BEAM INEACH REARCORNERFRONT VIEW OF BALERWARNING: BEFOR

Check external hoses for chafing, rubbing, leakage, or other deterioration anddamage. Tighten all fittings as necessary. Check hydraulic cyli

1.2.3.4.5.6.7.8.9.10.11.12.13.PRESSURE SETTINGHYDRAULIC SYSTEM PRESSURE SETTINGDANGER: DO NOT CLIMB ON SIDES OF BALER. USE A LADDER OR WORK PLATFORMWH

PRESSURE SETTING AND INTERLOCK TESTINGDANGER: DO NOT CLIMB ON SIDES OF BALER. USE A LADDER OR WORK PLATFORMWHEN WORKING ON TOP OF THE BALER OR OTHER A

CYLINDER REMOVAL AND REBUILDINGCYLINDER REMOVALClose the feed gate.Turn on power and lower the platen using the MANUAL DOWN button. Turn off power.Dis

Introduction ... 1-1EC Declaration of Conformity...

FEED GATE LATCH A D J U S T M E N TFEED GATELATCHSPRINGFEED GATESTRIKERTENSIONADJUSTMENTNUTNOTE: Adjustment is made by tightening orloosening the TEN

PRINCIPLES OF OPERATION2-8OPERATING CHARACTERISTICS:With the key switch in the ON position, and the bale door and feed gate closed, pressing theAUTOCY

FULL LOADAMPERAGEDISCONNECTSIZE (MAX)TIME DELAYFUSE (MAX)INVERSE TIMECIRCUIT BREAKER (MAX)30 m60 m90 mCHARTS2-92 MAINTENANCEELECTRICAL REQUIREMENTS16

PANEL BOX2-10TERMINALBLOCKMOTORSTARTERW/OVERLOADS2 AMPFUSERELAYS AND BASESTERMINAL STRIPGROUNDGROUNDTIMEROVERLOADADJUSTMENT2 MAINTENANCE

POWER UNIT2-11BREATHER CAPDIRECTIONAL CONTROLVALVESUBPLATERELIEF VALVE (RV1)SIGHT GAUGECOUNTERBALANCE VALVESUCTION FILTER(LOCATED INRESERVOIR)CLEAN OU

ELECTRICAL SCHEMATIC2-12E-64152 MAINTENANCE

HYDRAULIC SCHEMATIC2-132 MAINTENANCEE-04895 HP / 3.7 KW6 GPM / 22.7LPM

PARTS LIST2-14WARRANTY AND SERVICE ON MOTORSIf the baler motor fails under warranty, have it checked by a qualified electrician or service person. Ift

These instructions are not intended as a substitute for training andexperience in proper use, safety procedures, maintenance, or installatio

ANCHORING TO CONCRETE PAD3-2The concrete pad should be level, and a minimum of 3000 PSI concrete,steel reinforced, 150mm thick. Anchor baler to floor

1 OPERATIONINTRODUCTIONTHANK YOU FOR PURCHASING A MARATHON VERTICAL BALER. This product is designed to give you reliable service and superior perform

06-0045460VOLTSDANGERThe panel box contains high voltagecomponents. Only authorized servicepersonnel should be allowed inside.See Lock-Out

WARNING: BEFORE START-UP, REPLACE THE 3/4” PLUG ON THE TOP OF THEPOWER UNIT R E S E R VOIR WITH THE FILLER BREATHER CAP. THIS CAP I SSHIPPED IN

EC DECLARATION OF CONFORMITYThe Supply of Machinery (Safety) Regulations 1992Pursuant to The Council of The European Communities Directive 89/392/EEC,

PRE-OPERATING INSTRUCTIONS06-0045460VOLTSDANGERNEVER ENTER ANY PART OF THE BALER UNLESS THE DISCONNECTSWITCH HAS BEEN TURNED OFF AND PADLOCKED. Before

1 OPERATIONC O N T R O L S1-4MANUAL DOWN BUTTONRED WARNING LIGHTKEYED ON/OFF SWITCHMANUAL UP BUTTONBALE MADE LIGHTEMERGENCY STOP BUTTONCONTROL PANELF

1 OPERATIONCONTROL DESCRIPTION1.2.3.4.5.6.7.1-5ON-OFF (Keyed Selector Switch)Turning this switch to the ON position activates the other controls in t

IN CASE OF EMERGENCY:Push the large red button toSTOPOPERATING INSTRUCTIONS - MAKING A BALEWA R N I N G : DO NOT O P E R ATE BALER UNTIL O P E R AT

OPERATING INSTRUCTIONS - BALE TIE OFF/BALE EJECT 1-7When the “BALE MADE” light comes on it is time to tie off the bale and eject the balefrom the bale